#Separation studio printing problems manual

First you need to remove the paper feed assembly and then you can get to the clips that hold them on. Just unsnap them and replace them with the new roller. Rollers will normally come in a maintenance kit but they may need to be replaced approximately half way through the maintenance kit cycle. Here are some common feed rollers with their part numbers. There are many types of rollers and feed systems. They are still inexpensive and they will last you longer and you will have fewer headaches. For the best repair I use genuine OEM feed rollers. I have mixed feeling about these because I have had to go back and change them again later. You can also use generic rollers manufactured for almost all equipment. It works but I am inclined to use the real thing. On old copiers or printers that you can no longer get parts for you can apply clear silicon on the feed surface and let it dry twenty four hours. I have never used this but I have been told it will get you up and running. They also have some that stretch over the old rollers. Just peel off the adhesive and wrap it around the worn roller surface. It works with some styles mainly half moon styles. I have used it when I didn't have the right roller in my car stock. There is a material called feed roller tape. Some alternatives to replacing feed rollers: Once you get it where you can clean the roller repeat the procedure above.

This takes some patience and practice but it is better than damaging the clutch. You can also start the copy process and shut off the machine exactly when the feed roller engages. First you can actuate the clutch by pushing down on the solenoid or release lever. WARNING: If you try and turn these to clean them you will damage the clutch mechanism! There are two ways you can clean these types. These are harder to clean because they have a clutch system that keeps it at home position when not feeding. One feed roller and one separation roller. One Pre-feed roller, this pushes the paper into the other rollers. As I said there are many different types. Then go over it again with the dry part of the towel. Start by cleaning the roller and spinning it all the way around not missing any of the surfaces of the roller. This can be WD-40 or your favorite roller rejuvenator. Grab your towel and saturate it with cleaning fluid. Shine your flashlight into the paper feed area and locate the rubber rollers that feed the paper in. It dries out the tread and the remaining tread will get ripped off and then it still will not feed.

Note: Never use alcohol to clean rollers. Now that you have ruled out a blocked paper path, you can clean the feed roller(s).ДЇlashlight, strong cotton towel (so it will not rip off in the machine), WD-40 or Rubber roller rejuvenator. Shine your flashlight into the paper feed area and see if there are any pieces of paper torn off inside or something blocking the paper path. But if it jams at the cassette or paper tray area the next step is removing the paper tray. If it is jamming in the center of the machine, again it is a different problem. If it is jamming in the exit for instance, you have another problem. By doing this you are determining where the paper is jamming. If you need the specific tray to be functional we will get busy with the repair.ДЇirst make a single copy in the tray that is jamming. This will get you up and running quicker than cleaning the rollers.Дetermining if the rollers are the problem:

#Separation studio printing problems manual

I also would try using the bypass tray or manual feed tray if so equipped. The sensors are set for a specific timing and it will know the difference in length from letter size and legal size. The machine will think it is a different size and it will jam. Make sure when you change cassettes that the copier registers the correct size. Which paper tray? Is it tray 1 or tray 2? Also which size is jamming? On machines that have more than one paper tray you can switch paper trays and then you can skip cleaning the rollers. When your machine is jamming, first locate where the paper is jamming. The purpose of this article is to show you how you can clean or rejuvenate the rollers long enough for you to complete your job and have your repair person come out and fix it properly. When a roller is worn and dirty they will cause paper jams.

Most are made out of rubber and just like the tires on your car they wear out. Sure you can call the repair person, but you need the copies now! There's nothing you can do, or is there?ДЄll office equipment that feeds paper has a component inside that pulls the paper out of the paper tray and into the machine. You clear the jam but it keeps jamming! It's not pulling in the paper. You begin with your project and the copier jams. It's 8:30AM and your meeting is at 9:00AM. So you need ten sets of a fifty page document for this mornings meeting.